国产在线 | 日韩,疯狂做受xxxx高潮不断,影音先锋女人aa鲁色资源,欧美丰满熟妇xxxx性大屁股

產品描述:

概述：General Information

對于輪胎粉碎工業，我們需要高產量強動力高壽命的粉碎機。本粉碎機采用超強合金刀具保證使用壽命，堅固機架，大功率電機，引風出料分離系統保障物料出料順暢與分離纖維。
For the business to crush tyre, it is an urgent for high output crusher with high power and long service life. This crusher uses the super alloy cutter to guarantee the service life, and uses the solid frame, high power motor and induced discharge’s separation system to discharge smoothly and separate from fiber easily. 

用途：Purpose

用于粉碎含有細小鋼絲的大膠塊，分離纖維。
   The crusher is used to crush the rubber block with small steel wire, and make it separate from fiber.

調整刀具間隙：Adjusting gap of cutter

固定其中一把定刀，以此調整三把主軸上的活動刀于定刀間隙（0.6~1mm），根據活動刀再固定*后一把定刀。
Fixing one cutter, and then adjusting the 3 movable cutters at the main shaft and the gap of the fixed cutter (0.6~1mm); afterwards, fix the last cutter according to the movable cutter.

開機檢查：Inspection before start-up

在使用前應檢查各部緊固是否松動，打開加料蓋，手動轉動主軸檢查刀具與機腔篩網是否異常。合上加料蓋并固定，啟動電機空轉機器，聽機器是否有異常聲音，看各傳動、轉動部件是否平穩。
Inspect if the fasteners at each section unfasten or not; open the feeding cover, turn the main shaft by hand to see if cutter and sieve works normally; close and fix the feeding cover, and then start the motor to make the crusher run without load, at this time, it should hear if there is any abnormal sound; and see if each transmission component or rotatable part works stably.

注意事項：Precautions

本機轉動時不得將手或身體某部置于機器中，粉碎腔內不能進入大于1.5mm鐵或金屬類堅硬物質。
When the crusher works, it is prohibited to put hand or body into the machine; no hard materials, such as the metal with a size of 1.5mm are allowed to access to the crushing cavity. 

特點：Features

本機為一體結構，安裝方便、效益高（每小時400~600kg）。出料細度可根據需要跟換篩網。
The crusher is of an all-in-one structure, it can be installed easily, and work high efficiently (400~600kg per hour). The change of sieve is subject to the fineness of discharge. 

安裝與維護：Installation and maintenance

本機可獨立置于水平地面，需地腳固定。
The crusher can be placed on the ground horizontally, fixing by the foundation bolts.

各部運動處因每1000小時加油脂一次。

Each 1000 hours the rotating places must be injected the oil grease for lubrication.

失效與解決：Failure and troubleshooting

1、    電機不轉：檢查各區電路，手動轉動刀軸是否靈活。修整電路、跟換或調整轉動部件。Motor fails to work: check the circuit; turn cutter’s shaft by hand to see if it works flexibly; repair circuit, replace or adjust the rotatable components.

2、    出料不暢機腔過熱：檢查風機是否反轉，風管是否密封，風管、出料口是否堵塞，篩網是否過細。Discharging is blocked or machine is too hot: check if fan works reversely or air pipe is sealed; check if air pipe or discharging opening is blocked and sieve pore is too small.

產量達不到要求：檢查刀具鋒利程度，進料出料是否順暢，粉碎要求超標。
Output is far less than the given capability: check if the cutter is sharp as usual, if the feeding and discharging goes smoothly; if crushing exceeds the given standard.